Things To Know About Installing A Car Stereo System

Don't remove all of the wires now. Purchase a car stereo that will fit your car. Attach the antenna wire. Remove and reattach the wires in the following order: the positive wires, then the negative wires, then the ground (black) wire. Remove the front dash panel according to the directions in your owner's manual. Consider putting all of the screws into a small plastic baggie to make sure that they don't get lost during the car stereo installation process. Unscrew and pull out your car stereo unit and look at the back. One of the easiest ways to save money on car stereo texas systems is to install them yourself.

Disconnect the negative battery cable so that you can work safely. Slide the new car stereo into the mounting bracket. Slide the stereo into place but don't screw it in until you've tested it.For the Houston Car audio installation, you'll need your owner's manual, a screwdriver and socket wrench set, and wire strippers. For some people, a great-sounding car stereo system is an essential piece of equipment. Then attach the constant and ignition power wires.There's nothing like driving down the street and listening to music with the windows down.

You need them as a map to help you attach the new car stereo system. Your manual should show exactly how to do this.When testing the stereo, use the balance features to listen to each car stereo speaker and make sure that it's working properly. You will either see one plug that is attached to all of the wires or a bunch of wires that are individually attached to the stereo. The ground wire should be attached to metal.It's also a good idea to look for a system that is wired specifically for your make and model if you can find one.

If you don't have a plug, you'll need to wire it manually. It will save you a lot of time and effort. If you have a plug, all you need to do is remove it and plug in the new one.If everything's working right, go ahead and screw in your new stereo, put on some music, and enjoy!

16.10.17 08:29, kommentieren

Werbung


Facts That You Must Know About Car Stereo Installation

If you find the professionals charge a good deal of money to set up the car stereo, you can do it yourself and save that amount paid towards the expert.

It is not very difficult to install a car audio system; it is just that it seems so. You only need a bit of precision and focus to put up the system. No specialized skills or intimate knowledge on car audio is required for this purpose. You can actually put the excess money that you save from the installation process behind the best car audio system itself, thus giving you the scope to buy something better.

While initiating the process, you need to be careful as loss of concentration may lead to the damage of equipments of your car and spoil the quality of the car stereo installation system. You need to be systematic as the plugs go into their respective sockets only.

Getting started

After you purchase a new car audio system, see if it is fitting properly to the place of the old audio system. Along with your new car stereo system, also buy a cabling strap which is mechanized according to the car and stereo model and works brilliantly for new car stereo systems.

Before you get down to your car stereo repair Houston work, arrange for few tools like electrical tape, wire strippers, screwdrivers and wire cutters.

If you are not able to unscrew out the old audio system, take some guidance on the right way to remove it from your dashboard where the new car stereo will fit in.

Removing the old car stereo

At first, detach the negative cable from the battery as you should never work with that cable connected.

Take out the dash board of your car to remove the old car audio system and check the wires that are linked at the back. Either there would be a single plug with too many wires attached to them or else a cluster of single wires. In case of the later one, it is best to disconnect them one at a time to avoid confusion.

Put the connectors into the new cabling strap and plug it back into your new car stereo.

If you have successfully done this, you can leave out on the next section.

Connecting the Wiring Manually For better  Navigation system in Houston

If there is no cabling strap support, attach each of the wires at the back of the back of the new car stereo very carefully.

Slowly detect the positive wires from each speaker and connect them at the back of the positive connector of the new car stereo. Similarly, do the same with the negative wires of each speaker and connect them to the negative connectors of the car audio system. In case, if there is only one wire coming out from the speakers, the speakers are grounded at the chassis and you would have to install a new wiring for the speakers.

The negative wire, attached with metal and not plastic should be connected with a screw near the radio in the dash.

The ignition wires and the 12 constant, both positive is supposed to be connected together to the back of the new stereo.

Putting in the car stereo

All the wires should be attached to a single connector which is coming out from the additional cabling strap or the one which came along with the car stereo system where all the wires have been connected to.

If there is no new bracket to place the new car stereo, use the old one that previously held the factory stereo system.

Now put the final connector which is the cabling strap at the back of the stereo system along with the antenna, a long wire which was previously connected at the back of the old stereo and the power wire at the back of the new car stereo unit.

Put the stereo system inside the dashboard where the previous system was placed but do not put back the screws as you may require testing the system.

Now is the time when you should again attach back the negative cable to the battery.

Start your car as well as power on the car stereo unit. Check keenly, whether all the speakers attached is working fine.

Put the screws back into the stereo system and put the cover of the dash board back on.

In case results are unsatisfactory

If you still find the system is not delivering satisfying results, you can use a wooden or fiberglass flummox with which the sound quality will get better and you can even include noise reduction objects like liners, glue strips, put in more carpets on the inner panel and use sprays.

16.10.17 08:29, kommentieren


Werbung